DETAIL KOLEKSI

Microwave speed meter


Oleh : Djoni Tirtaatmadia

Info Katalog

Penerbit : FTI - Usakti

Kota Terbit : Jakarta

Tahun Terbit : 1994

Pembimbing 1 : Tony Winata

Pembimbing 2 : Zacharias Santoso

Subyek : Telecommunication;Electrical engineering

Kata Kunci : microwave, speed meter

Status Posting : Published

Status : Tidak Lengkap


File Repositori
No. Nama File Hal. Link
1. 1994_TA_STE_06290080_Halaman-Judul.pdf 10
2. 1994_TA_STE_06290080_Lembar-Pengesahan.pdf
3. 1994_TA_STE_06290080_Bab-1_Pendahuluan.pdf 4
4. 1994_TA_STE_06290080_Bab-2_Teori-Penunjang.pdf
5. 1994_TA_STE_06290080_Bab-3_Realisasi.pdf
6. 1994_TA_STE_06290080_Bab-4_Kalibrasi.pdf
7. 1994_TA_STE_06290080_Bab-5_Kesimpulan-dan-Saran.pdf
8. 1994_TA_STE_06290080_Daftar-Pustaka.pdf 1
9. 1994_TA_STE_06290080_Lampiran.pdf

T Tugas akhir ini adalah sebuah alat untuk mengukur besar kecepatan linier suatu target dengan mempergunakan prinsip efek Doppler. Besar pergeseran frekuensi (frequency shift) yang disebabkan oleh target bergantung pada besar kecepatan linier target tersebut. Gelombang yang digunakan untuk pengukuran ini adalah gelombang mikro pada frekuensi 10,23 GHz (dalam daerah frekuensi X-band) sehingga pergeseran frekuensi yang diperoleh dari pengukuran kecepatan target (antara 20 km/jam hingga 100 km/jam) berada pada daerah frekuensi audio (20 Hz - 20 KHz). Pergeseran frekuensi tersebut dikonversikan menjadi tegangan searah yang besarnya berbanding lurus dengan pergeseran frekuensi tersebut. Nilai tegangan yang dibaca pada meter menunjukkan besar kecepatan target yang diukur. Perubahan tegangan output untuk tiap perbedaan kecepatan 10 km/jam adalah liner, sebesar 0,92625 volt. Komponen yang digunakan untuk mendapatkan pergeseran frekuensi pada alat ini adalah Gunnplexer yang terdiri atas Gunn diode, Schottky mixer diode serta Circulator.

T This final project is a tool to measure the linear velocity of a target using the principle of the Doppler effect. The magnitude of the frequency shift caused by the target depends on the magnitude of the linear velocity of the target. The waves used for this measurement are microwaves at a frequency of 10.23 GHz (in the X-band frequency region) so that the frequency shift obtained from measuring the target speed (between 20 km/h to 100 km/h) is in the audio frequency region (20 Hz - 20 KHz). The frequency shift is converted into a direct voltage whose magnitude is directly proportional to the frequency shift. The voltage value read on the meter indicates the magnitude of the measured target speed. The change in output voltage for every 10 km/h speed difference is linear, amounting to 0.92625 volts. The components used to obtain the frequency shift in this tool are Gunnplexer which consists of Gunn diode, Schottky mixer diode and Circulator.

Bagaimana Anda menilai Koleksi ini ?